We are happy to announce we have launched the Crowdfunding campaign a few minutes ago!

As promised you are the first to be informed.

To say  THANK YOU for being with us for so long, we created a secret LOYALTY PERK just for you, so that you can get the drone at the lowest possible price. It is only visible via this link: https://www.indiegogo.com/projects/2465306/x/20266304?secret_perk_token=868d2942

If you cannot support us financially, please help by sharing the campaign via social media. By doing that you also have a chance to get a FREE Drone

Thank You!

Hello

Another X- TANKCOPTER update here.

In the beginning, we would like to share a new video of the TankCopter, and kindly ask you to help us out a little bit. We would be extremely glad if you could share the website (https://xerall.com) or the video with your friends or family. This would definitely help us to get more exposure and get more interest in the project. For the ”early bird” backers, we will have the special offer 33% discount (for the whole set: Drone, VR, TX,)

Regarding the shipment status, we are still at the progress of preparing the campaign, building a mailing list. Probably we will launch the campaign around October and begin the shipment straight after.

Before the campaign launch, we will refund your orders and ask you to join us and re-purchase the model via Kickstarter. This will help us to build ”campaign momentum” and you will be the first to know about ”early bird” offer. We will make sure it is the most valuable pledge.

Thank you for being with us for so long, all the support received. Hopefully, we are not far from launching the X-TANKCOPTER in the market. Once this happens we will bring you more advanced drone the X-CARCOPTER
https://xerall.com/category/x-carcopter/
Maybe one day a Flying Car in a scale 1:1 capable of carrying a human https://xerall.com/category/flying-car-scale-11/

Hello

Another TankCopter update here.

Below are the videos from first field testing. Please have in mind it was filmed with smartphones so the quality is poor, this week we will work with a cinematic camera, therefore you will soon see the full review of the drone in nicer quality.

The second video is the endurance test (maybe boring) but it only shows the flight endurance of the model.

https://www.youtube.com/watch?v=2ddMrMlNmYc&t

We have done over 50 runs with the model, so far it looks very good. It has a good climbing rate, is very stable in the flight, the altitude hold mode works well (very handy for the beginners), it has good endurance.  The drone is able to drive on most of the surfaces, even short grass. It is really fast, climbs well over obstacles. The hinges in the arms, function as expected: arms simply rotate once they collide with an obstacle (instead of breaking).

The camera has no ”jelly effect”, its field of view is precisely positioned, so the top corners represent the place of the tip of the arms, which is handy to judge if the drone will make through the opening etc. Also, the camera hood works great and prevents against flares and mechanical damage.
The packaging is solid, we used polystyrene inserts ( instead of the plastic or paper), so we are sure the model will arrive at your doorstep safe and sound 🙂

We finished the drone’s instruction manual: download
We got all necessary certification, so we are ready to press the mass production button. But here is a little problem on the way: Despite the long negotiation with the factory. They will not start the production below the order of 4000 units (MOQ). As they have to open the assembly line: train staff, equip the line with necessary tools, order components in high quantity etc. At the moment we need to sale an additional 1900 units to complete the order.  As we missing funds to complete order ourselves, due to the fact we just got billed for the international patent also tooling costed more than we initially calculated.

In order to accelerate the process, this week we started looking for the distributors, retailers, that could help us complete the order. We will also run a quick Crowdfunding campaign.

As you noticed the drone got significantly cheaper 149 USD instead of 199USD, that comes from the fact we got final price confirmation from the factory. So surely we will refund the difference to you. But we also wonder if we should make the full refund and ask you to help us during the Crowdfunding campaign ( it would help us to create momentum, consequently better campaign visibility). Please allow us few days to investigate

We are very grateful for your support and patience, but we understand some of you cannot wait any longer, therefore please have in mind you can request the full refund at any time by emailing us at [email protected]

Hello

Another production progress update here.

I am happy to say, that we are moving really fast in the recent weeks 🙂

We got out of the way:

1. The final colour scheme for the TankCopter.

The drone will look like this :

2. The packaging inserts.

Those will be made out of polystyrene instead of plastic. Reasons behind our choice :
– Plastic inserts don’t look very aesthetic, as they tend to deform, bend.
– Polystyrene inserts provide better protection for the drone.

3. Tested the idea that prevents arms damage (the snap-lock mechanism + arm on the hinge).

https://www.youtube.com/watch?v=K5zy72Cj_wY

4. The app got a new look.

5. The ”Instruction Manual” for the smartphone app is also finished.

You can download it here: https://xerall.com/downloads/

6. We decided on the smaller radio transmitter.

Reasons behind our choice:

– The most important one; it smaller, lighter, therefore uses less plastic, which lowers impact on the environment. Also, because the size and weight, the shipping cost and carbon footprint are also reduced.

– Those buttons under the index fingers are really convenient. In had it feels similar to Sony PlayStation joystick.

Things ahead of us :

1. Packaging Graphics.
2. Instruction Manual ( for the drone and the radio transmitter).
3. Short Kickstarter campaign in order to get to at least lowest MOQ ( Minimum Order Quantity).

Please, do worry about the time involved in the campaign, your model will be shipped as soon as it is ready ( before the campaign finishes).

Hello

Another update from the factory, here.

Below pictures of the first injection moulded model. Due to the fact the injection moulded plastic is lighter, stiffer from the one we used in 3D printing, the final model performance is significantly improved. Stiffer propellers produce more thrust. The reduced weight of all plastic components additionally increases the thrust to weight ratio.

Ahead of us is choosing the final paint style for the TankCopter and packaging design. Factory ensured us, they will be ready us ship a small batch of final product around the end of May.

https://www.youtube.com/watch?v=crgv2B0GEU0

Video footage sent to us ( sorry for the bad quality). The TankCopter despite the fact it has to carry the caterpillar tracks, has good climbing ratio and is agile as any other quadcopter.

We were asked to confirm on the controller, so we decided to also ask for your opinion too.

Please let us know in the comments which controller you like more.

1.Recently proposed  Radio Controller

The controller is smaller in size, it has hidden antennas, also convenient to use mode buttons under the index finger.

2. The current Controller

This one is bigger in size, therefore feels better in hand, but it has external antennas and buttons accessible via thumb ( which may be inconvenient as thumbs should stay on sticks).

Range and functionality stay the same for both.

Dear all

In the beginning, I would like to apologise for a long time since the last update.

I would like to kindly announce that we have started the production phase on 10.01.2018. It was the day we have finally confirmed the drawing together with the factory and began the tooling phase, it took a bit longer than I have initially thought.

The tooling takes 8-12 weeks, as we will use harden steel ( not rapid tooling). Then we will have 1-2 weeks for the final testing and corrections.

In the meanwhile, I work on the packaging design, instruction manual etc.

I have spoken to the factory, three days ago, and I was told the tooling is halfway down and we can expect a ready model at the end of March. Currently, they celebrate the New Year, therefore the factory is closed until 26th February.

Before that, I have decided to apply two last changes to the drawing, that I think will make the product better. First is the back arm design, ( now is a bit lighter and slimmer, lighter and more flexible -harder to damage). The second one, quite important is how arm attaches to the drone’s body.
Below are the details:

I know you have been waiting for so long for the model ( me too), and all you are amazing backers! That means a lot to me, thanks to you the project continues, and it is already in the last stage. I would like to give something in return for your patience. I will just wait for the factory to confirm the final pricing and I will update you what it will be.

Please remember you have right to get full refund at any time.

I would also like to share the good news, as you may notice, there quite a few designs of human-carrying drones, like Ehang https://www.youtube.com/watch?v=F8shiw6zY_A.

I was asked to draw a draft of future Flying Car, that can be presented to potential investors. I took few days off and drafted the full-size idea; I hope you like it.

I hope this idea one day will be reality, fingers crossed.

BTW Please join Xerall’s Facebook page at : https://www.facebook.com/xerall/

DEAR TANKCOPTER FANS

Firstly, my apologies for a long time since the last update.

The reason was simple when there is money involved there is a problem ?. We spend over 4 weeks just negotiating the tooling agreement with the factory, the whole process took much longer than initially estimated. We had to make corrections then send the document to the lawyers for review and back to the factory, (5 times) before we found common ground.

Ahead of us is the manufacturing contract, but that has only one paragraph that worries us, the 4000 MOQ, from which we are far away ☹ in terms of pre-orders. But there is also the positive information; the factory will fulfil the current order at slightly higher price, so there is no reason to worry about yours pre-orders.

As you can see in the graphic above, there is a quite a lot of components to produce, in order to make this relatively simple idea alive. We went through them all very carefully, as we have limited funds, therefore, we need to get tooling right at the first time.

We finally received the Production TimeLine Plan from the manufacturer which looks as follow:

1. Tooling  – 35 days (We will start the tooling from next Monday)
2. Engineering phase – 16 days
3. FEP(Final Engineering Pilot ) – 12 days
4. PP(Pre-production) 14 days – that is the moment when we will start shipping your orders
5. PS(Production start)

Seeing that time-consuming process ( agreement negotiations). We decided to have a look at recently released 8.5x23mm motors, we took them on the test bench to see if there are any better from the currently used (8.5x20mm). The result was as expected, the thrust was slightly increased so we decided to implement them (small change in CAD). It is a little upgrade but always a score.

As the project takes more time to complete than initially estimated, we fully understand that some of you cannot wait any longer. Please have in mind that you can withdraw your order and receive full refund at any requested time, in that matter please contact us at [email protected]

Thank you for being with us 🙂